KeyMaker X2

 

Home
Up
Read this First
KeyMaker X1
KeyMaker LCD
Buy Now
Delivery times
Firmware Update
Functionality Upgrade
Damaged Board
Safety Precautions
User's Guides
EEPROM Locations
Customer Feedback
New Page 3

Joe in Australia offers the only Affordable Fully Assembled, Programmed and Tested unlimited use USB based ThinkPad Supervisor Password [SVP] Recovery or Clear Tools in the world. 

It provides the elegant convenience of a dedicated, fully assembled and tested, Ready To Use USB based ThinkPad SVP  Recovery or Clear tool which unlocks an unlimited number of TPs together with detailed illustrated step by step instructions which everyone can understand and follow.

Joe's KeyMaker X2 [KMX2] can Recover or Clear Supervisor Password from most current IBM and Lenovo ThinkPad models with the exception of those models which do not store the Supervisor Password in an EEPROM, not supported models are SL300 SL400 SL500 G550 T*40 T440 T450 T540 X*40 W540 W541 X240 X250 X1 Carbon (Gen 2) and (Gen3) Helix Gen3.

Joe's KeyMaker X2 is no longer sold.

KMX2 board Width is the same as a Credit Card, Length is slightly less than a Credit card.


Note: If you purchase a Standard off the shelf Seeeduino Mega board from someone else it will ONLY perform its normal Arduino function. It will NOT perform any of Joe's proprietary KMX2 firmware functions.

KMX2 is a Seeeduino Mega programmed with Joes's proprietary KMX2 firmware.

Every KMX2 board potentially has 3 levels of functionality - KMX2, KMX2 PRO and KMX2 PRO Plus.

Same board, same firmware, different level of functionality depending on which Product Key has been typed into that board.

A KMX2 can have its level of functionality changed at ANY TIME by purchasing a Product Key Upgrade for that level.

This allows you to buy the level of functionality you require and NOT have to worry if you got it wrong as your decision is not final.

For example you decide the plain KMX2 is all you need, later on you come across a ThinkPad that for example has a CRC2 error, you can then purchase the KMX2 PRO Product Key and have that Product Key emailed to you, enter that Product Key into your KMX2 and instantly from that point on it is a KMX2 PRO with all the KMX2 PRO functionality.

Note: KMX2 is currently OUT OF STOCK

KMX2 - will recover and display the unencrypted Supervisor Password [SVP] so you can type it in at the password prompt. 

If TPM/TCPA/PC8394T/8356908 security was enabled then the SVP is encrypted and therefore it cannot be displayed for typing in at the password prompt. The recovered SVP is displayed however it consists of a bunch of apparently random hex numbers which you cannot type in at the alphanumeric password prompt.

KMX2 - will Zap or Clear any encrypted TPM/TCPA/PC8394T/8356908  Supervisor Password [SVP]  The end result is the encrypted TPM/TCPA/PC8394T/8356908  SVP is gone you just donít get to know what the encrypted SVP was.

KMX2 can recover [or Zap pr Clear if encrypted] the SVP from every type of EEPROM ever used to store SVP in a ThinkPad; EEPROM types KMX2 can Read from or Write to include 93C46, C4C61, 24C01, 24C03, 24RF08, 24RF08 equivalent P24S08, PS08, L08, 08 as well as LSI EEPROM PC8394T and 8356908

KMX2 PRO  - Does everything KMX2 does PLUS it can Repair CRC1 and CRC2 errors as well as Read and Display or Write back entire EEPROM Data to and from  your PC and allow you to save that displayed EEPROM Data to an Intel HEX file, it can also can write back to the EEPROM Data from a saved and perhaps edited Intel HEX file which is useful when you have a ThinkPad that someone else has done things to without really knowing what they are doing.

KMX2 PRO Plus  - Does everything KMX2 and KMX2 PRO does PLUS each time you recover, display or clear or Zap a SVP it stores that password inside the KMX2 PRO Plus together with what type EEPROM it was from.

KMX2 PRO Plus can store and display the last 110 passwords Recovered or Cleared or Zapped 

What is this useful for ? 

You may quickly ZAP or even recover the SVP and type it in, a few minutes or hours or days later you suddenly wonder if the password [which by then you have forgotten] was encrypted or not and was there a chance it matched the Hard Disk Password as often people use the same SVP and HD password. With KMX2 PRO Plus it is easy, scroll through the display of the last 110 passwords and try them on the hard disk password.

NOTE: All KMX2 models save internally in Non Volatile Memory the last 110 passwords Recovered or Cleared or Zapped
           - ONLY KMX2 PRO Plus will display those saved passwords -

If you have a KMX2 or KMX2 PRO and need to display any of the last 110 passwords that have been saved, buying a KMX2 PRO Plus Product Key will enable you to display the last 110 passwords saved in the past on that KMX2 board.

KMX2 PRO Plus can read and store on the KMX2 board's Non Volatile Memory [NVM] 2 x complete EEPROM data.  The stored EEPROM Data can be written back to the EEPROM in a ThinkPad. This is useful if you have a nervous customer or perhaps you are nervous about working on the EEPROM to Clear or Zap or perform a CRC1 or CRC2 repair, before you start you can quickly save the entire EEPROM Data and be comfortable with the knowledge that you can restore it back to exactly how it was to start with.

There are many situations during the unlocking of a TP that are greatly assisted by having a copy of the original contents of the EEPROM.

What is included with KMX2

  1. KMX2 board fully assembled, tested and programmed with Joe's KeyMaker KMX2 Firmware.

  2. 4 way cable with 4 combined sockets at both ends
    ONLY 3 pins of this cable are used by most people.

  3. 4 way dual male header, used for attaching custom made cables.

  4. Documentation, right here on this web site KMX2 User's Guide, which includes detailed illustrated instructions on how to connect it to ALL the applicable TP models.

KMX2 with supplied 4 way cable depicted above, this cable will do 99% of all TP models.

What is NOT included with KMX2

EEPROM clips NOT SUPPLIED, you can easily make or purchase your own clips ..See section on clips options.

You will need to source your own Mini USB cable NOT SUPPLIED, you most likely already have a few of those.

Close-up view of KMX2, how is it connected. 

Mini USB cable [not supplied] connects to the Mini USB connector [top left] to your PC, MAC or Linux system and the supplied 4 way cable connects the 4 pin I2C header [bottom right] to the EEPROM in your ThinkPad.

Only 3 connections GND, SCL and SDA are used 99% of the time. 

Those are ALL the required connections.

NO MORE excuses for not turning that Password Locked door-stop back into a working TP.

Designed and programmed entirely by Joe in Australia who has been unlocking TP's for the past 8 years and who has 30+ years experience in Microcontroller hardware and software design.

Joe's first innovation in TP unlocking (back in 2002) was to unlock TP's  without having to unsolder the EEPROM. Many have copied that and other innovations from Joe in Australia. Some even like to pretend  they thought of it first.

Just remember:  you ALWAYS see it here first.  Joe's KeyMaker KMX2 with its unique ZAP SVP feature is yet another first.

USB ports are everywhere, antiquated RS-232 ports are almost extinct.

No need to waste time and money sourcing parts that, depending on where you buy them, can easily cost a lot MORE than the assembled and tested KMX2s. Ready to go - it does not get easier than that.

You can start work immediately on unlocking your TP instead of being forced to do a short Electronics crash-course before you can even start.

You can keep it REALLY SIMPLE and just zap that pesky Supervisor Password by pressing the ZAP SVP button on the board, no charts to consult at all, no guesswork.

It isn't fudged by using bit-banging, it is done properly with a fully compliant i2c hardware interface.

The entire Program runs inside the onboard ATmeg2560 MCU. To interact with you, it  only requires that you install the appropriate USB driver for your system and any one of the numerous freely available "Terminal Software programs" on your PC, MAC or Linux System. 

Can handle all LSI and 24RF08 EEPROM based TP models.

All operations can be repeated an UNLIMITED NUMBER OF Times, on any number of different TPs.

Can either ZAP Supervisor passwords (SVPs) an unlimited number of times or Recover and Display SVP, including clearing LSI encrypted passwords from any number of different TPs.

You will be hard pressed to find anything that even comes close to KMX2 PRO Plus in one quality state of the art feature rich convenient USB powered TP unlocking tool that does it ALL.

You are NOT excluded if you have a MAC or prefer to run Linux 

The reason, is KMX2 is a powerful state of the art Microcontroller based board with an USB interface, ALL THE WORK is done ON the board by the Microcontroller and my firmware program,  you ONLY need a Personal Computer of some kind to interact with the program running on the board and display the results whilst performing Initial Activation or if you wish to perform more advanced operation which require a 2nd PC. 

All you need to install on your PC, MAC or Linux Personal Computer is;

  1. USB drivers for the FTDI FT232RL USB chip, Detailed installation guides for FTDI USB drivers

  2. Any one of the many FREE Terminal Software programs, GOOGLE for "Free Terminal Software".
    I prefer to use Tera Term for Windows, actual software download is here.

FTDI USB Drivers are compatible with the following operating systems; 

Windows Server 2008 R2

Windows 7

Windows 7 x64

Windows Server 2008

Windows Server 2008 x64

Windows Vista

Windows Vista x64

Windows Server 2003

Windows Server 2003 x64

Windows XP

Windows XP x64

Windows 2000

Windows ME

Windows 98

Linux

Mac OS X

Mac OS 9

Mac OS 8

Windows CE.NET (Version 4.2 and greater)

KMX2 

NOTE: some of the images and video below depict a KMX1 board, the KMX2 board is slightly larger and the Zap SVP button is in a different position on the board.

For the basic operations described below KMX2 works the same way as KMX1. I will update these images and video to show an KMX2 in operation.

What sets the KMX2 PRO PLUS apart is the Non Volatile Memory [NVM] operations which allows saving the contents of the entire TP EEPROM and also allows programming a TP EEPROM from that EEPROM data previously saved in the KMX2 NVM, the saved data is retained even when power to KMX2 is switched off. KMX2 has the capacity to save two [2] complete TP EEPROMS.

KMX2 Zap 

KMX2 powered by a USB Port on the locked TP, using the Zap SVP button on KMX2. Works with TP models which on the EEPROM Locations webpage it states to "treat as 24RF08" or "treat as LSI"

KMX1 Zap SVP button unlocking a Pass phrase SVP from an R60
 

KMX2 + LCD   

KMX2 used together with the KMX-LCD [KMX-LCD is NOT included, sold separately] powered by a USB Port on the locked TP, using the Joystick to scroll through menus and select nearly all possible operations with excellent status display. 

KMX-LCD board plugs in on top of the KMX2 board, the KMX-LCD has an I2C connector which includes the protection resistors, KMX-LCD is controlled by the user operating the Joystick.

The secondary Zap SVP button on the KMX-LCD or pushing down on the Joystick can also be used to Zap SVP on TP models which on the EEPROM Locations webpage it states to "treat as 24RF08" or "treat as LSI", the LCD provides additional status information not available without the KMX-LCD.

KMX-LCD displaying recovered SVP 'ABCDDEFG' ready to type in on a QWERTY 'US' keyboard, you can also select to display the recovered SVP for typing in on a  German or French keyboard. The KMX-LCD also displays the 5 second delay countdown after the ZAP SVP button is pressed, delay can be set to 0,5,10 or 15 seconds. 

Video - KMX1 working together with [prototype]  KMX-LCD recovering and Clearing Supervisor Password from a Lenovo R60
NOTE: There are in fact 2 ITEMS, a KMX1 with the KMX-LCD plugged in on top of the KMX1.
KMX-LCD on its own does NOTHING!

 

KMX2 + PC 

KMX1 powered by a USB Port on ANOTHER PC or Laptop, using Terminal Software on the PC to display KMX1 menus and status. Works with all TP models. 

Additionally with KMX2 PRO Plus the PC can be used to save Intel HEX files of complete EEPROMS which can also be written back to the EEPROM in the TP

NOTE: Another PC or Laptop is required, NOT the locked TP which obviously cannot be used to run any software before it is unlocked.

 

NOTE: if you already have a KMX2 PRO Plus follow the instructions in the KMX2 User's Guide the instructions here are a simplified OVERVIEW missing important detail.

KMX2

Stand Alone mode simply means that you do not need any other PC or Laptop - just the KMX2 PRO Plus board with its ZAP SVP button and power from the USB port of the password locked TP.

You can Zap/unlock an unlimited number of TPs.

You really want to unlock your TP and use it again?

The example below explains how to use KMX1 to Zap a SVP using KMX1 in Stand Alone mode

Well it doesn't get easier than this!

You can easily do it yourself! NO shipping ,NO wondering and NO worrying if you will ever see your TP again. 

NO Electronics crash course to complete, NO endless forums to read, NO guesswork.

Nothing to build and wonder if you got it right.

You don't have to become a Geek to get the job done.

KMX2 arrives fully assembled, tested and ready to use - You know it will work when you switch it on.

You can devote all your effort to the task of actually Zapping/Clearing that pesky Supervisor Password even if encrypted TPM/TCPA/PC8394T/8356908  security has been enabled.

You have access to detailed illustrated instructions right here including details of how to identify which TP model you have, which EEPROM type is in your model TP and how to gain access to it.

First, you Hook up 3 wires to your Password Protected TP, you can use clips or sharp probes to make the connections, then Switch your TP ON

Your TP is asking you to enter the Supervisor Password? 

Well now you have the tools to Clear the Supervisor Password!  

Even if the optional TPM/TCPA/PC8394T/8356908  Security (encryption) was enabled, not a problem.

You simply depress the Zap SVP button on your KMX2 PRO Plus, button over on mid right. 

The default 5 second delay [can be changed to 0, 5 or 15 seconds] starts counting down in seconds and flash the EEPROM Activity LED each second until it counts down to zero.

The green EEPROM activity LED will light up on the board which lets you know that the EEPROM is being accessed, the LED will remain lit for about 15 seconds while the SVP is cleared.

The green LED will briefly turn OFF.

If the operation was successfully completed the LED will turn ON for 1/2 second, OFF for 1/2 second and back ON for 1/2 second, in other words 2 SLOW flashes of the green LED means all is OK. Your pesky SVP is GONE!

If the operation fails you will see a FAST burst of flashes from the green LED signifying the SVP was not cleared which usually means your 3 EEPROM connections are wrong or became disconnected during the operation. You can check the connections and try again. 

Switch OFF your TP, switch it back ON again and it will NOT ask you for a SVP, as if it never existed.

Your TP is now unlocked

Time to congratulate yourself on a job well done.

Below are photos of an R52 being unlocked, using KMX2 PRO Plus in Stand Alone mode. 

The R52 has been opened and placed on its side to allow access to the ON/OFF push button and also to allow access to the underside of the R52.

The Memory cover underneath the R52 has been removed to allow access to the EEPROM connection points, only 1 screw to undo.

KMX2 is powered by the USB port of the R52 which is being unlocked

Making the 2 probes used is described here

No other PC or anything else is required.

A black clip is being used for the GND connection attached to the metal clip which normally holds the Memory in place.

Leaving one hand free to operate the Zap SVP button.

Looks easy - because - it is easy when you have the right tools.

You can find the EEPROM location and connection points for the R52 in this case on the EEPROM Locations page, there you can find the R52 page which has the photo below of the R52 EEPROM connections.

The 2 probes held in place, GND clip visible at bottom of photo.

The KMX2 PRO Plus Zap SVP button is pressed, button over on mid right. 

The default 5 second delay [can be changed to 0, 5 or 15 seconds] counts down in seconds and flashes the EEPROM Activity LED once each second until it counts down to zero.

The green EEPROM activity LED will light up on the board which lets you know that the EEPROM is being accessed, the LED will remain lit for about 15 seconds while the SVP is cleared.

The green LED will briefly turn OFF.

If the operation was successfully completed the green LED will deliver  4 SLOW flashes to signal that all is OK. Your pesky SVP is GONE!

If the operation fails you will see a FAST burst of flashes from the green LED signifying the SVP was not cleared which usually means your 3 EEPROM connections are wrong or became disconnected during the operation. You can check the connections and try again. 

Switch OFF your TP, switch it back ON again and it will NOT ask you for a SVP, as if it never existed.

Your TP is now unlocked

You have full access to your TP

Time to congratulate yourself on a job well done.

Please take careful NOTE

3 wires are connected INSIDE the locked TP to its EEPROM, NOT to a USB port

Only the KMX2 board itself is connected to the USB Port on the locked TP. In the Stand Alone mode the USB cable is only used to supply power to the KMX2 PRO Plus board.

When used with a second PC or Laptop to display recovered SVP, the USB connection is also used to interact with the firmware (program) inside the ATMega2560 MCU on the KMX2 PRO Plus board and also to display progress and results on your PC or laptop Screen.

This is NOT some new found magical way to unlock a TP without having to connect to an EEPROM inside the locked TP

Physically connecting to the EEPROM inside a locked TP cannot be avoided this is the ONLY way a Password Locked TP can be unlocked.

There is no other way to access the EEPROM inside the locked TP in order to unlock it.

KMX2 

Read more here about using KMX2 PRO Plus with a second PC or Laptop

Below are photos of an R52 being unlocked using another R52 to run the Terminal software and power the KMX1.

The password locked R52 has been opened and placed on its side to allow access to the ON/OFF push button and also to allow access to the underside of the R52.

The Memory cover underneath the R52 has been removed, the Memory has also been removed to allow access to the EEPROM connection points, only 1 screw to undo.

KMX2 is powered by the USB port of the second R52, the one running the Terminal Software to communicate with KMX1.

Making the 2 probes used is described here

Nothing else is required.

A black clip is being used for the GND connection attached to the metal clip which normally holds the Memory in place.

Leaving one hand free to operate the Terminal Software, in some case you may need 2 persons.

Looks easy - because - it is easy when you have the right tools.

You can find the EEPROM location and connection points for the R52 in this case on the EEPROM Locations page, there you can find the R52 page which has the photo below of the R52 EEPROM connections.

The 2 probes held in place, GND clip not visible clipped to finger on left that holds memory in place.

 

Recovered Password QAZYSVP displayed ready to type in at the password prompt using a QWERTY English Keyboard 

Note : how different the same SVP is for another country QWERTZ or AZERTY Keyboard, pay attention to this when recovering SVP.

Your type in the recovered SVP QAZYSV at the password prompt

Your TP is now unlocked,  as a reward, you are greeted by this welcome sign of an UNLOCKED TP

Now you have full access to your TP

Time to congratulate yourself on a job well done.

Once you have unlocked your TP, I would recommend that you set a new Supervisor Password, one you can remember. If you don't set one someone else can and you may have to do this all over again, much easier to set your own password so no one else can set one and frustrate you.

*BADCS* or *NVPC* displayed INSTEAD OF THE SVP  

This happens when TPM/TCPA/PC8394T/8356908 security has been enabled and the SVP is ENCRYPTED so what you see displayed is NOT something you can simply type in at the password prompt.

This is NOT a problem. KMX2 can perform CLEAR SVP and the encrypted TPM/TCPA/PC8394T/8356908 SVP will be gone.

A quick lesson;

When using KMX2 connection leads to the EEPROM inside a TP can be connected whilst the TP is switched OFF or ON, the leads can be left connected while the TP is being switched ON and OFF.

If you are new to TP unlocking you might be thinking - so what! well read on and you will see what a significant difference that can make.

RS-232 based simple interfaces when connected to the EEPROM inside a TP impose a substantial load on the EEPROM's signal lines and if left connected will interfere with the power on and power off functions of the TP. 

Which means that when using an old RS-232 interface the EEPROM leads  must be disconnected while the TP is powering up, connected to perform a function then disconnected again before switching the TP OFF. 

When using an old RS-232 interface the EEPROM leads can ONLY be connected after the TP has been switched ON and has completed its power up functions.

A lot of TP unlock operations require that you Power Cycle the TP, in other words Switch OFF, Switch ON the TP, having to disconnect leads from the EEPROM and  reconnect those EEPROM leads each time the TP is switched ON or OFF becomes tedious and can lead to mistakes.

Another plus for Joe's KeyMaker KMX2 PRO.

Full Read/Write/SAVE/Edit access to the contents of the Security Chip and CRC Repair level

The CRC repair is a basic routine that corrects the CRC error caused by illegal data ending up in the wrong place - improper power off or other hardware caused issues (A2x owners know about this).

ThinkPads whose SVP can be removed using the KMX2 Zap SVP Button are those model TPs  which on the EEPROM Locations page state "treat as 24RF08" or "treat as LSI" with one exception - do NOT use ZAP SVP or Clear SVP on the R30, with R30 RECOVER the SVP and type it in at the keyboard.

KMX2 PRO Plus Compared to KMX 2 PRO

KMX2 PRO PLUS has ALL the Features of KMX2 PRO S as well as additional features

KMX2 PRO Plus displays the last 110 Zapped or Recovered Passwords which are saved by ALL KMX2 series KeyMakers.

All KMX2 series KeyMakers store in Non Volatile Memory (NVM) the last 110 Supervisor Password Zapped, Recovered or Cleared. 

Only KMX2 PRO PLUS can display the saved passwords, KMX2 saves them but will not display them. If you have a KMX2 and need to display a password that has been saved then upgrading to the KMX2 PRO Plus Product Key  will allow you to see those  passwords saved before you upgraded the KMX2 or KMX2 PRO.

A useful feature if you removed the SVP using the Zap SVP button or Clear SVP command without ever having seen the Supervisor Password or even if you did see it and typed it in but you did not write it down before removing it then later when you could no longer remember the SVP wondered if that SVP may have been recoverable and you may have been able to use it to check if the Hard Disk password was the same.

Now you can scroll back through the last 110 recovered or cleared passwords and see what the password was unless TPM/TCPA/PC8394T/8356908  was enabled in which case it will display that fact.

KMX2 PRO Plus93C46, C4C61, 24C01, 24C03, 24RF08, 24RF08 equivalent such as P24S08, PS08, L08, 08 as well as LSI EEPROM such as PC8394T and 8356908 are all covered.

Useful on difficult unlocks [with a very nervous customer] or if you are worried you may make matters worse, you can save the entire EEPROM contents with the comforting knowledge that you can program the data back exactly how it was before you did anything to it.

Command 9, Saved Passwords available in KMX2 PRO Plus

KMX2 PRO Plus
Command 9, in any EEPROM Menu,  Save-Display-Program 24RF08 to and from NVM shown below

Note: these are displays that can exceed the vertical height of the screen, in actual use you can scroll back and forth using the Mouse Wheel in Tera Term. Here I am showing you overlapping screen captures.

Displaying the EEPROM Data saved in KMX2 PRO Plus NVM in Intel Hex format allows one to highlight - copy - and paste the text into a text editor and save all the EEPROM Data as an Intel HEX file on the PC or Laptop used to run the Tera Term Software. That saved Intel HEX file can later be used to Program another EEPROM with KMX2 PRO or KMX2 PRO Plus.

 

KMX2 PRO Plus Top of the KeyMaker KMX2 range - has all possible features to tackle difficult password recovery operations for example when the TP is reporting lots of errors or when you suspect that the TP you purchased at Auction was heavily corrupted by someone before you who had no clue and followed all the incorrect ThinkPad Password recovery ideas to be found on the net.

In addition to all the KMX1PROS features KMX2 PRO Plus can display the last 110 Zapped, Recovered or Cleared Supervisor Passwords. As well as copy 2 entire EEPROMS into NVM which is retained even when KMX2 is switched off.

This a must have tool for any Professional who unlocks a lot of different TPs

KMX2 Compared to KMX2 PRO and KMX2 PRO Plus  -   KMX2 PRO Plus has additional features

KMX2 PRO and KMX2 PRO Plus Displays Recovered Passwords for US, German and French Keyboards at the same time.

KMX2 Displays Recovered SVP in the currently selected Country Keyboard

KMX2 PRO and KMX2 PRO Plus can Read and Display entire EEPROM Data as Hex and ASCII. KMX2 Displays only the Recovered SVP

KMX2 PRO and KMX2 PRO Plus can Read and Display entire EEPROM Data as an Intel hex file format, which can be saved to a file on the PC and later used as to program an entire EPROM or edited and then used to program an entire EEPROM.

KMX2 PRO and KMX2 PRO Plus can Program entire EEPROM Data from an Intel Hex file, for example one that was previously saved and or edited.

KMX2 PRO and KMX2 PRO Plus can Repair CRC1 and CR2 Errors.

KMX2 PRO Plus has all possible features to tackle difficult password recovery operations for example when the TP is reporting lots of errors or when you suspect that the TP you purchased at Auction was heavily corrupted by someone before you who had no clue and followed all the incorrect ThinkPad Password recovery ideas to be found on the net.

Allows one to safely try things after one has FIRST quickly conveniently backed up the entire contents of the TP EEPROM into KMX2 PRO Plus NVM, with the comforting knowledge that you can try a lot of ways of solving various issues and always be able to program it back the way you first saved it and try something different.

Read and writes entire EEPROM contents to and from Intel HEX files which can be saved on your PC or Laptop.

Displays recovered SVP for all keyboard languages at the same time, sometimes this clearly highlights the huge differences some password can have when displayed for a different Country Keyboard.

KMX2 PRO Plus is a must have tool for any Professional who unlocks a lot of different TPs

Disclaimer

I make no warranty that any of my information is correct, or safe, or does or does not breach any warranty clause,  or anything else, it is up to you to decide if you will follow all or any of the instructions to recover the Supervisor Password from a TP. It is up to you to decide, I am not responsible for the results or for any consequential or incidental damages whatsoever.

This site maintained by Joe in Australia

Last updated on Monday, 12 December 2016 06:31:15 PM  

 If you have any questions WHICH ARE NOT ALREADY COVERED IN THESE PAGES , email Joe at

Hit Counter